Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revisionBoth sides next revision
articles:m104_hfm_intake_rebuild [2020/11/19 09:26] – [Remove fuel rail] john5788articles:m104_hfm_intake_rebuild [2020/11/21 07:49] john5788
Line 98: Line 98:
 </grid> </grid>
 ==== Remove intake manifold ==== ==== Remove intake manifold ====
 +<grid> 
 +<col sm="6"> 
 +  - Unbolt remaining bolts holding intake manifold to cylinder head 
 +  - Loosen both hose clamps connecting the upper and lower intake manifolds together. Located underneath the upper intake manifold 
 +  - Disconnect wire to resonator flap 
 +  - Disconnect air hoses near oil dipstick mounting bracket 
 +  - Lift up and remove air intake manifold 
 +</col> 
 +<col sm="6"> 
 +<grid> 
 +<col sm="6"> 
 +<thumbnail> 
 +{{ articles:m104lowerintakeboot.jpg?300 }} 
 +<caption>Loosening lower intake boot</caption> 
 +</thumbnail> 
 +</col> 
 +<col sm="6"> 
 +<thumbnail> 
 +{{ articles:m104airhoses.jpg?300 }} 
 +<caption>Air hoses underneath intake manifold</caption> 
 +</thumbnail> 
 +</col> 
 +<col sm="6"> 
 +<thumbnail> 
 +{{ articles:m104wirethrottlebody.jpg?300 }} 
 +<caption>Disconnect wire for resonator flap near the throttle body </caption> 
 +</thumbnail> 
 +</col> 
 +</grid> 
 +</col> 
 +</grid>
 ==== Rebuild ==== ==== Rebuild ====
 +
 +<grid>
 +<col sm="6">
 +  - Replace all vacuum lines
 +  - Clean parts
 +    - Intake manifold seat on cylinder head
 +    - Intake manifold
 +    - Throttle body boot if not replacing
 +    - Intake boots if not replacing
 +  - Parts to replace
 +    - Intake manifold gaskets (104 141 1080, requires 6)
 +    - Long lower intake hose (104 094 35 82)
 +    - Short lower intake hose (104 094 36 82)
 +    - Fuel injector seal (019 997 13 48, requires 12)
 +</col>
 +<col sm="6">
 +<grid>
 +<col sm="6">
 +<thumbnail>
 +{{ articles:m104vacuumparts.jpg?300 }}
 +<caption>Vacuum parts to replace</caption>
 +</thumbnail>
 +</col>
 +<col sm="6">
 +<thumbnail>
 +{{ articles:m104cleanthrottlebootandintakeseat.jpg?300 }}
 +<caption>Cleaned throttle body boot and intake manifold seat on cylinder head</caption>
 +</thumbnail>
 +</col>
 +<col sm="6">
 +<thumbnail>
 +{{ articles:m104intakerebuilt.jpg?300 }}
 +<caption>Intake manifold cleaned up and rebuilt with new gaskets and hoses</caption>
 +</thumbnail>
 +</col>
 +<col sm="6">
 +<thumbnail>
 +{{ articles:m104injector.jpg?300 }}
 +<caption>M104 injector with 2 seals that need to be replaced </caption>
 +</thumbnail>
 +</col>
 +</grid>
 +</col>
 +</grid>
  • articles/m104_hfm_intake_rebuild.txt
  • Last modified: 2020/11/21 07:50
  • by john5788