Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
| articles:m104_hfm_intake_rebuild [2020/11/19 08:17] – created john5788 | articles:m104_hfm_intake_rebuild [2020/11/21 07:50] (current) – john5788 | ||
|---|---|---|---|
| Line 10: | Line 10: | ||
| ^ Parts Required | Intake manifold gaskets (104 141 1080, requires 6) \\ Long lower intake hose (104 094 35 82) \\ Short lower intake hose (104 094 36 82) \\ Fuel injector seal (019 997 13 48, requires 12) | | ^ Parts Required | Intake manifold gaskets (104 141 1080, requires 6) \\ Long lower intake hose (104 094 35 82) \\ Short lower intake hose (104 094 36 82) \\ Fuel injector seal (019 997 13 48, requires 12) | | ||
| ^ Applicable models | All HFM injected M104 engines | | ^ Applicable models | All HFM injected M104 engines | | ||
| + | </ | ||
| + | </ | ||
| + | |||
| + | ===== Remove air intake pipe ===== | ||
| + | < | ||
| + | <col sm=" | ||
| + | - Unclip retaining hooks at air box behind right headlight and remove upper lid | ||
| + | - Unplug both sensors along the intake pipe | ||
| + | - Remove valve cover screws | ||
| + | - Loosen upper hose clamp at throttle body boot | ||
| + | - Pull up on air intake pipe and remove | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | </ | ||
| + | |||
| + | ===== Remove fuel rail ===== | ||
| + | < | ||
| + | <col sm=" | ||
| + | - Remove black plastic engine wiring harness cover | ||
| + | - Remove fuel pressure bleed cap located towards the center of the fuel rail | ||
| + | - Bleed excess fuel pressure by pressing schrader valve with a tool like a small screwdriver and replace the cap | ||
| + | - Disconnect fuel inlet and return hoses from fuel rail | ||
| + | - Make note of which hose goes where | ||
| + | - Remove fuel pressure regulator vacuum line | ||
| + | - Unbolt dipstick for clearance by removing 5mm allen bolt | ||
| + | - Unplug fuel injectors from engine harness by pinching connectors and pulling | ||
| + | - Metal clips may not bend all the way and a thin screwdriver can be used to gently bend the metal clips for clearance | ||
| + | - Unbolt fuel rail and pull to remove. There are 5x 6mm allen bolts holding it in place. | ||
| + | </ | ||
| + | </ | ||
| + | |||
| + | < | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | </ | ||
| + | |||
| + | ===== Remove intake manifold ===== | ||
| + | < | ||
| + | <col sm=" | ||
| + | - Unbolt remaining bolts holding intake manifold to cylinder head | ||
| + | - Loosen both hose clamps connecting the upper and lower intake manifolds together. Located underneath the upper intake manifold | ||
| + | - Disconnect wire to resonator flap | ||
| + | - Disconnect air hoses near oil dipstick mounting bracket | ||
| + | - Lift up and remove air intake manifold | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | </ | ||
| + | </ | ||
| + | </ | ||
| + | |||
| + | ===== Rebuild ===== | ||
| + | < | ||
| + | <col sm=" | ||
| + | - Replace all vacuum lines | ||
| + | - Clean parts | ||
| + | - Intake manifold seat on cylinder head | ||
| + | - Intake manifold | ||
| + | - Throttle body boot if not replacing | ||
| + | - Intake boots if not replacing | ||
| + | - Parts to replace | ||
| + | - Intake manifold gaskets (104 141 1080, requires 6) | ||
| + | - Long lower intake hose (104 094 35 82) | ||
| + | - Short lower intake hose (104 094 36 82) | ||
| + | - Fuel injector seal (019 997 13 48, requires 12) | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | <col sm=" | ||
| + | < | ||
| + | {{ articles: | ||
| + | < | ||
| + | </ | ||
| + | </ | ||
| + | </ | ||
| </ | </ | ||
| </ | </ | ||